Concrobium Mold Control, Dual Purpose, Non-toxic Anti-microbial, For Mold Remediation & Prevention, 3.78L Gallon (620004)

CODE: 620-004

Concrobium Mold Control. Dual Purpose, Non-toxic Anti-microbial. For mold remediation and prevention. Concrobium Mold Control offers mold remediation and prevention in a single solution, making it a versatile antimicrobial for restoration pros. The EPA-registered product can be deployed during the “knock down” phases of restoration projects to control mold spore proliferation, and can be applied on restored surfaces for ongoing mold protection.

The odorless, category lV solution contains no harmful chemicals and requires no special handling or personal protective equipment. It contains zero VOCs, making it the ideal solution for restoration contractors with customers who are chemically-sensitive.

Features

• Fungistat, mildewsat, deodorizer
• Single solution kills and prevents mold
• No bleach, ammonia or VOCs
• EPA-registered for fungicide and fungistat
• Requires zero isolation time and has no odour
• Can be fogged to treat large and inaccessible spaces
• Ready to use solution, no mixing required

Specifications

• Coverage:  Aerosol - up to 150 sq ft. Manual/Compression Sprayer - 350-400 sq ft per gallon. Fogging: approximately 1,400 sq ft total surface coverage (walls, floors, ceiling) per 1/2 gallon
• Form:  Liquid
• Colour:  Clear
• Odour:  Odourless
• Active ingredient:  Sodium Carbonate
• pH:  11 to 11.5
• Package size:  3.8L Gallon (4 gal per case)
• Ready to use:  Yes
• Shelf life:  NA
• EPA Registration No.:  82552-1
• Dilution:  RTU
• Recommended uses:  Disaster restoration, construction and renovation, specialty mold clean-up and prevention, can be used in homes, businesses, institutions, cottages, RVs, boats – anywhere that mold takes hold.
• Product code:  620004

Product Application

Mold Control Pro is effective against mold and mildew organisms on both hard and fabric surfaces that have been subjected to wet environments. If in doubt, test on a small, inconspicuous section. Wipe materials vulnerable to water marks immediately after contact with Mold Control Pro. Over application may result in residue formation, which can be wiped away with a Mold Control dampened cloth.

Personal protection equipment requirements for applicators: For areas less than 30 square feet, an N-95 respirator, gloves and goggles/eye protection are recommended to avoid mold or mold spore exposure. For areas greater than 30 square feet, use an N-95 respirator or half-face respirator with HEPA filter, disposable overalls, glove and goggles/eye protection.

Note: Mold Control Pro is ready to use - do not dilute.

Before applying, correct conditions favorable to mold growth.

Application to eliminate mold small areas (Total Surface Area Affected Less Than 30 Square Feet). Apply by cloth, hand-spray, electric or compression spray, cold fogger, paintbrush, roller or immersion.

1. Remove heavy soil (Mold Control Pro must come in direct contact with mold to be effective).
2. Apply product on area until evenly wet.
3. If desired, wipe off excess wetness.
4. Allow treated surfaces to dry completely.

Note: Do not expect Mold Control Pro to whiten stains on contact. If mold stains remain, reapply product and wipe or scrub area. In some cases, staining may be irreversible. If additional steps are taken to remove or cover the stain, reapply Mold Control Pro as a final step to protect area from regrowth.

Large areas (Total Surface Area Affected Greater Than 30 Square Feet). Areas larger than 30 square feet require special procedures and individuals trained in remediation. Refer to the recommended websites for guidelines on remediation.

Before using Mold Control Pro to mitigate large areas, you should understand one or more of these guidelines. Follow these guidelines to apply Mold Control Pro. Mold Control Pro must be used as part of a comprehensive mold remediation or water damage restoration program, including:

• Monitoring for conditions favorable to mold growth such as water leaks and high relative humidity
• Eliminating conditions favorable to mold growth
• Drying affected areas to below 20% moisture content.

Application to prevent mold:

1. Apply Concrobium Mold Control Pro on area until evenly wet.
2. If desired, wipe off excess wetness.
3. Allow treated surfaces to dry completely.

Reapplication: Reapply weekly or when growth or odor reappears. Determine and correct the cause of regrowth before reapplication. Reapply Concrobium Mold Control Pro if surfaces are washed or painted.